- BootROM 1.08 Booting from NAND flash High speed PHY - Version: 2.1.2 (COM-PHY-V20) Update PEX Device ID 0x67100 High speed PHY - Ended Successfully DDR3 Training Sequence - Ver 4.5.0 DDR3 Training Sequence - Ended Successfully Status = MV_OK BootROM: Image checksum verification PASSED ** LOADER ** U-Boot 2011.12 (Dec 24 2013 - 20:21:45) Marvell version: v2011.12 2013_Q1.2 (ALPHA U-BOOT : 1.0) Board: RD-88F6710_ALpha_KingsCanyon SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200 [MHz] L2 @ 600 [MHz] TClock @ 200 [MHz] DDR @ 600 [MHz] DDR 16Bit Width, FastPath Memory Access DRAM: 512 MiB Map: Code: 0x1fef5000:0x1ff9faac BSS: 0x1ffef784 Stack: 0x1f9f4ef8 Heap: 0x1f9f5000:0x1fef5000 NAND: flash id : daad 256 MiB MMC: MRVL_MMC: 0 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 PEX 0.0(0): Detected No Link. PEX 0.1(1): Detected No Link. FPU not initialized USB 0: Host Mode USB 1: Host Mode Modules/Interfaces Detected: RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) Not Marvell PHY id1 ffff id2 ffff Enable HD1 Enable HD2 Net: egiga1 Warning: egiga1 MAC addresses don't match: Address in SROM is AA:BB:CC:DD:EE Address in environment is AA:BB:CC:DD:FF Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x500000, size 0x500000 5242880 bytes read: OK NAND read: device 0 offset 0xa00000, size 0x500000 5242880 bytes read: OK ## Booting image at 00a00000 ... ## Booting kernel from Legacy Image at 00a00000 ... Image Name: Linux-3.2.40 Created: 2015-07-31 8:04:21 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3115304 Bytes = 3 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 00f00000 ... Image Name: Ramdisk Created: 2015-10-13 10:20:10 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 2106880 Bytes = 2 MiB Load Address: 00e00000 Entry Point: 00e00000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 3.2.40 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #4 Fri Jul 31 16:04:18 CST 2015 CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Marvell Armada-370 Using UBoot passing parameters structure >>>>>>>Tag MAC AA:BB:CC:DD:EE >>>>>>>Tag MAC AA:BB:CC:DD:EE Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping off. Total pages: 16368 Kernel command line: root=/dev/ram console=ttyS0,115200 max_loop=32 PID hash table entries: 2048 (order: -2, 8192 bytes) Dentry cache hash table entries: 65536 (order: 3, 262144 bytes) Inode-cache hash table entries: 32768 (order: 2, 131072 bytes) allocated 262144 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 512MB = 512MB total Memory: 506528k/506528k available, 17760k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff8000 ( 32 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xfa800000 (1440 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x805b8000 (5824 kB) .init : 0x805b8000 - 0x805e8000 ( 192 kB) .data : 0x805e8000 - 0x80620a20 ( 227 kB) .bss : 0x80620a44 - 0x8066aa38 ( 296 kB) NR_IRQS:256 a370_time_init sched_clock: 32 bits at 600MHz, resolution 1ns, wraps every 7158ms Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 4096 Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices CPU: Testing write buffer coherency: ok hw perfevents: no hardware support available devtmpfs: initialized xor: measuring software checksum speed arm4regs : 169.600 MB/sec 8regs : 166.400 MB/sec 32regs : 166.400 MB/sec xor: using function: arm4regs (169.600 MB/sec) NET: Registered protocol family 16 L0 cache Enabled Speculative Prefetch Disabled Aurora L2 Cache Enabled Support IO coherency. Enable DLB and DRAM write coalescing CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 512MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable DEVICE_CS0 ....base f2000000, size 32MB DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEVICE_CS3 ....no such PEX0_MEM ....base e0000000, size 32MB PEX0_IO ....base f1100000, size 1MB PEX1_MEM ....base e2000000, size 32MB PEX1_IO ....base f1200000, size 1MB INTER_REGS ....base f1000000, size 1MB DMA_UART ....no such SPI_CS0 ....base f0000000, size 16MB SPI_CS1 ....no such SPI_CS2 ....no such SPI_CS3 ....no such SPI_CS4 ....no such SPI_CS5 ....no such SPI_CS6 ....no such SPI_CS7 ....no such BOOT_ROM_CS ....no such DEV_BOOTCS ....base f5000000, size 16MB PMU_SCRATCHPAD ....no such CRYPT0_ENG ....base c8010000, size 64KB Marvell Armada370 Board-- RD-88F6710_Alpha Soc: MV6710 A1 LE LSP version: linux-3.2.y-2013_Q1.2p2 (32KB SW Page Size) Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000 Marvell USB EHCI Host controller #0: 90017920 Marvell USB EHCI Host controller #1: 90017720 PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled bio: create slab at 0 raid6: int32x1 334 MB/s raid6: int32x2 353 MB/s raid6: int32x4 275 MB/s raid6: int32x8 280 MB/s raid6: using algorithm int32x2 (353 MB/s) SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource armada370_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 8192 (order: 0, 32768 bytes) TCP established hash table entries: 16384 (order: 2, 131072 bytes) TCP bind hash table entries: 16384 (order: 1, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 2048 (order: 0, 32768 bytes) UDP-Lite hash table entries: 2048 (order: 0, 32768 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... rootfs image is not initramfs (no cpio magic); looks like an initrd Freeing initrd memory: 2016K CESA test started: bufNum = 1, bufSize = 20000 Cesa Test Start: pMbufSrc=90024060, pFragsSrc=90272000, pMbufDst=90023860, pFragsDst=90270000 mvCesaInit: channels=1, session=32, queue=256 cesadev_init(805bfbe4) Armada XP hwmon thermal sensor initialized. Initializing Armada-XP CPU power management (WFI) VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 8192 (order 0, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). fuse init (API version 7.17) SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 992 async_tx: api initialized (async) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Initializing ths8200_init Initializing dove_adi9889_init mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor ) mv_xor mv_xor.1: Marvell XOR: ( xor ) mv_xor mv_xor.2: Marvell XOR: ( cpy ) mv_xor mv_xor.3: Marvell XOR: ( fill cpy ) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 41) is a 16550A console [ttyS0] enabled serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 42) is a 16550A brd: module loaded loop: module loaded sata_mv sata_mv.0: slots 32 ports 2 scsi0 : sata_mv scsi1 : sata_mv ata1: SATA max UDMA/133 irq 55 ata2: SATA max UDMA/133 irq 55 armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC flash read_id : daad NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit) Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 Creating 7 MTD partitions on "armada-nand": 0x000000000000-0x000000500000 : "u-Boot" 0x000000500000-0x000000a00000 : "uImage" 0x000000a00000-0x000000f00000 : "ramdisk" 0x000000f00000-0x00000d800000 : "image.cfs" 0x00000dd00000-0x00000ec00000 : "rescue firmware" 0x00000ec00000-0x000010000000 : "config" 0x00000d800000-0x00000dd00000 : "reserve" mv_eth_probe: port_mask=0x3, cpu_mask=0x1 o 2 Giga ports supported o SKB recycle supported (Enabled) o NETA acceleration mode 1 o RX Queue support: 1 Queues * 128 Descriptors o TX Queue support: 1 Queues * 532 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Loading network interface(s) o Warning: GbE port 0 is not connected to PHY/RGMII/Switch, skip initialization o Port 1 is connected to Linux netdevice giga p=1: mtu=1500, mac=900b1e6c o egiga0, ifindex = 2, GbE port = 1 sky2: driver version 1.30 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.1: Marvell Orion EHCI ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100 ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 ata1: SATA link down (SStatus 0 SControl F300) registered taskstats version 1 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD10EZEX-22BN5A0, 01.01A01, max UDMA/133 ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD10EZEX-22B 01.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 1:0:0:0: [sda] 4096-byte physical blocks sd 1:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: unknown partition table sd 1:0:0:0: [sda] Attached SCSI disk md: Skipping autodetection of RAID arrays. (raid=autodetect will force) RAMDISK: gzip image found at block 0 VFS: Mounted root (ext2 filesystem) on device 1:0. Freeing init memory: 192K init started: BusyBox v1.20.2 (2014-10-30 15:26:14 CST) starting pid 463, tty '': '/etc/rc.sh' ** Mounting /etc/fstab umount: can't umount /proc: Invalid argument umount: can't umount /usr/local/modules: Invalid argument sh: hotPlug.sh: not found sh: can't open '/usr/sbin/pre_usb.sh' sh: can't open '/usr/sbin/pre_usb.sh' UBI: attaching mtd5 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 5051 UBI: attached mtd5 to ubi0 UBI: MTD device name: "config" UBI: MTD device size: 20 MiB UBI: number of good PEBs: 152 UBI: number of bad PEBs: 8 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 22 UBI: total number of reserved PEBs: 130 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 42/33 UBI: image sequence number: -1950777852 UBI: background thread "ubi_bgt0d" started, PID 483 UBI device number 0, total 152 LEBs (19300352 bytes, 18.4 MiB), available 22 LEBs (2793472 bytes, 2.7 MiB), LEB size 126976 bytes (124.0 KiB) UBIFS: mounted UBI device 0, volume 0, name "config" UBIFS: file system size: 14602240 bytes (14260 KiB, 13 MiB, 115 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 689699 bytes (673 KiB) umount: can't umount /usr/local/tmp/image.cfs: No such file or directory rm: can't remove '/usr/local/tmp/image.cfs': No such file or directory umount: can't umount /usr/local/tmp: Invalid argument first good block is 0 image len = 98660352 , image checksum = 17768b63 umount: can't umount /usr/local/tmp: Invalid argument dump image checksum=17768b63 mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules cp: can't stat '/tmp1/*': No such file or directory ln: /lib/./liblber-2.4.so.2.5.6: File exists ln: /lib/./libminiupnpc.so: File exists ln: /lib/./libnatpmp.so: File exists ln: /lib/./libpam.so.0.81.6: File exists ln: /usr/local/sbin/alert_email_config.sh: File exists ln: /usr/sbin/language.sh: File exists dev.raid.speed_limit_max = 1000 jnl: driver (lke_9.0.0 lke_9.0.0_r239626_b47, LBD=ON) loaded at 7f000000 ufsd: module license 'Commercial product' taints kernel. Disabling lock debugging due to kernel taint ufsd:: trace mask set to 0000000f ufsd: driver (lke_9.0.0 lke_9.0.0_r239626_b47, LBD=ON, acl, ioctl, bdi, sd2(0), fua, bz, tr) loaded at 7f020000 NTFS support included Hfs+/HfsJ support included optimized: speed Build_for__WD_Kings_Canyon_k3.2.40_32k_hybrid_2014-07-28_lke_9.0.0_r239626_b47 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_config -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_expand -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_expand_disks -> /usr/sbin/diskmgr lrwxrwxrwx 1 root 0 17 Jan 1 00:00 /usr/sbin//raid_update_info -> /usr/sbin/diskmgr hardware init first good block is 0 mtd check v1.06.06032015 config mtd type is UBIFS device = /usr/local/config Total size = 12500 Kbytes Used size = 384 Kbytes Free size = 12116 Kbytes percentage = 3 /usr/local/config free size is 12406784 ** copy config files *** Copy orion.db from flash **** cp: can't stat '/usr/local/modules/files/fan_temperature.txt': No such file or directory *** symlink onbrd.ini from flash **** ** set loopback interface UBI: attaching mtd6 to ubi1 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 36 UBI: attached mtd6 to ubi1 UBI: MTD device name: "reserve" UBI: MTD device size: 5 MiB UBI: number of good PEBs: 40 UBI: number of bad PEBs: 0 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 40 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 2/1 UBI: image sequence number: -744554858 UBI: background thread "ubi_bgt1d" started, PID 2415 UBI device number 1, total 40 LEBs (5079040 bytes, 4.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: mounted UBI device 1, volume 0, name "reserve" UBIFS: file system size: 3174400 bytes (3100 KiB, 3 MiB, 25 LEBs) UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: lzo UBIFS: reserved for root: 149934 bytes (146 KiB) UBIFS: un-mount UBI device 1, volume 0 first good block is 0 mac1 = 00:90:A9:E3:61:48 lan0:ifconfig egiga0 hw ether 00:90:A9:E3:61:48 egiga0: mac address changed egiga0: link up egiga0: started set lan0 speed Model ID : Zion first good block is 0 Zion ln: /usr/local/model/web/pages/images/./icon: File exists first good block is 0 hidden encryption: 1 old firmware ver:2.10.310.1013.2015 new firmware ver:2.10.310.1013.2015 rm: can't remove '/tmp/fix_wd_config': No such file or directory *** execute rc.init.sh awk: /var/run/udhcpc0.pid: No such file or directory RTNETLINK answers: Cannot assign requested address route: SIOCDELRT: No such process Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.11.10 port = 49152 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.11.10:49152/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized killall: crond: no process killed crond[2659]: crond: crond (busybox 1.20.2) started, log level 8 --1970-01-01 00:00:36-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.11.10 port = 49153 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.11.10:49153/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized sh: you need to specify whom to kill Advertisements Sent Advertisements Sent failed: Connection timed out. wget: unable to resolve host address 'download.wdc.com' *** Copy CacheVolume data from flash **** *** set Time Zone **** $Usage: apache {start|stop|restart} {web/dav} Thu Jan 1 01:00:58 CET 1970 *** get Time from rtc and set it into system **** rtc: RTC time = 2016/3/19 Sat 11:43:18 Sat Mar 19 12:43:18 CET 2016 Set Date & time : sntp -K /dev/null -S -r time.windows.com sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) Module IPC SERVER Version:(1.00.20090706) ads=0 created mail daemon thread 0 POWER ON DEVICE!! md0 state is HDIO_DRIVE_CMD(identify) failed: Inappropriate ioctl for device restart sysinfod... sysinfod: full update begin... Set Date & time : sntp -K /dev/null -S -r pool.ntp.org sntp 4.2.8@1.3265 Fri Jan 9 06:42:54 UTC 2015 (8) cat: can't open '/tmp/hw_detect_sata': No such file or directory sysinfod: disk connected: previous=0xffffffff, now=0x0 --2016-03-19 12:43:25-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... failed: Connection timed out. wget: unable to resolve host address 'download.wdc.com' sysinfod: Disk2(sda) detected. Starting system message bus PHY_LAN_NUMBER=1 BOND_ENABLE=0 VLAN0_ENABLE=0 VLAN1_ENABLE=0 --2016-03-19 12:43:28-- http://download.wdc.com/apps/WDMyCloudMirror/WDMyCloudMirror.xml Resolving download.wdc.com... I/O warning : failed to load external entity "/var/www/xml/internal_backup.xml" I/O warning : failed to load external entity "/var/www/xml/ftp_download.xml" /usr/local/modules/script/system_init: line 1062: /mnt/tmp6/ibuki/avahi_tm_serv: not found cat: can't open '/var/run/traceroute_wd.pid': No such file or directory ash: you need to specify whom to kill killall: traceroute: no process killed failed: Connection timed out. wget: unable to resolve host address 'download.wdc.com' --2016-03-19 12:43:33-- http://download.wdc.com/apps/WDMyCloudMirror/WDMyCloudMirror.xml Resolving download.wdc.com... sysinfod: disk connected: previous=0x0, now=0x2 --2016-03-19 12:43:35-- http://download.wdc.com/nas/WDMyCloudEX2_HDD_Blacklist.xml Resolving download.wdc.com... failed: Connection timed out. wget: unable to resolve host address 'download.wdc.com' waiting : [10] failed: Connection timed out. wget: unable to resolve host address 'download.wdc.com' mcu version 1.04 chk_io v1.04.20141112 system daemon v1.04.20141211 PIP is disabled, exiting. Sat Mar 19 12:43:42 CET 2016 - %W - Communication Manager - startup is disabled, use 'enable' to start process /usr/local/modules/script/system_init: line 1288: vvctl: not found dev.raid.speed_limit_max = 200000 killall: chk_hotplug: no process killed Please press Enter to activate this console. call load_module ### create systemfile ### /usr/sbin/load_module: line 541: can't create /sys/block/sdb/queue/read_ahead_kb: nonexistent directory ### sata_reload_application start ### Cannot get device settings: No such device Cannot get wake-on-lan settings: No such device Cannot get message level: No such device Cannot get link status: No such device Initializing UPnP Sdk with ipaddress = (null) port = 0 UPnP Initialized ipaddress= 192.168.11.10 port = 49154 Specifying the webserver root directory -- /etc/upnp Registering the RootDevice with desc_doc_url: http://192.168.11.10:49154/nasdevicedesc.xml RootDevice Registered Initializing State Table State Table Initialized Starting atopacctd Starting atop system monitor atop atop started Rename is FAILE USE 2nd Rename *** APKG Daemon is starting ... *** Advertisements Sent Rename is FAILE USE 2nd Rename killall: smbd: no process killed Starting wdnotifier sh: you need to specify whom to kill sh: you need to specify whom to kill wdnotifier started Sat Mar 19 12:43:49 CET 2016 /etc/init.d/onbrdnetloccommd - Start killall: smbd: no process killed killall: chk_blockip: no process killed killall: chk_blockip: no process killed sysinfod: full update begin... 3023 root 4096 S avahi-daemon: running [MyCloud.local] killall: elephantdriveDaemon: no process killed ### sata_reload_application end ### rm: can't remove '/tmp/disk_uuid': No such file or directory sysinfod: full update begin... LED_POWER_ON sysinfod: inform: all drives status=Healthy. traceroute: bad address 'www.wd2go.com' traceroute: bad address 'www.wdc.com' starting pid 3429, tty '/dev/ttyS0': '/bin/login' Password of admin: Login incorrect Password of admin: Login incorrect Password of admin: process '/bin/login' (pid 3429) exited. Scheduling for restart. Please press Enter to activate this console. starting pid 5848, tty '/dev/ttyS0': '/bin/login' Password of admin: ata2: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen ata2: edma_err_cause=00000020 pp_flags=00000000, SError=00180000 ata2: SError: { 10B8B Dispar } ata2: hard resetting link